884aa四虎影成人精品,99久久国产综合精品女图图等你,97在线观看永久免费视频,久久精品国产精品亚洲38,ⅵdeodesetv性欧美

（昆明理工大學建筑工程學院， 昆明 650000）

［摘要］通過設置四個不同的節點試件進行低周反復試驗，觀察四個節點的不同力學特性，重點分析滯回曲線、骨架曲線。對比環板節點和套筒節點試驗結果可以發現，新型的套筒節點的各項力學性能非常理想，不劣于傳統的環板節點。對比不同套筒厚度的套筒節點試驗結果，發現隨著套筒厚度的增加，套筒節點有更好的延性、塑性變形能力和耗能能力。套筒節點的性能提升幅度和套筒厚度不是正比關系，當套筒厚度較小時，隨著套筒厚度增加，節點性能提升幅度較大。當套筒厚度較大時，隨著套筒厚度增加，節點性能提升幅度較小。從經濟方面考慮，建議套筒厚度取10mm。

［關鍵詞］新型套筒鋼節點； 參數影響分析； 節點設計

中圖分類號：TU375-2文獻標識碼：A文章編號：1002-848X(2019)06-0066-03

Experimental study on sleeve joints of round steel tubes

Yan Minglei， Wang Junping， Li Zhangtao， Ren Simao

（College of Architectural Engineering， Kunming Institute of Technology， Kunming 650000， China）

Abstract:By setting four different node test pieces for low-cycle repeated test, the different mechanical properties of the four nodes were observed, and the hysteresis curves and skeleton curves were emphatically analyzed. Comparing the test results of the ring plate joint and the sleeve joint, it can be found that the mechanical properties of the new sleeve joint are very satisfactory and are not inferior to the traditional ring plate joint. Comparing the test results of the sleeve joints with different sleeve thicknesses, it is found that with the increase of the thickness of the sleeve, the sleeve joints have better ductility, plastic deformation ability and energy consumption. The performance improvement of the sleeve joint is not proportional to the thickness of the sleeve. When the thickness of the sleeve is small, the performance of the joint increases greatly as the thickness of the sleeve increases. When the thickness of the sleeve is large, as the thickness of the sleeve increases, the performance of the node is less increased. From the economic point of view,  the thickness of the sleeve should be 10mm.

Keywords:new sleeve steel joint; parameter influence analysis; node design

作者簡介：閆明磊，碩士研究生，Email:1138791264@qq.com。